Binho Supernova

Binho Supernova host adapter.
In this guide: Setup · Hardware reference · Protocols · Firmware · FAQ · Troubleshooting
Summary
Section titled “Summary”The Binho Supernova is a USB host adapter that connects the computer to I3C, I2C, SPI and UART buses and to six GPIO pins. Each protocol has its own pins, and all of them can run at the same time.
| Feature | Binho Supernova |
|---|---|
| Host PC link | USB Full Speed |
| Downstream power | 1.2 to 3.3 V |
| Power monitoring | No |
| GPIO pins | 6 dedicated pins |
| Logic levels | 1.2 to 3.3 V (I3C: 0.8 to 3.3 V) |
I3CController and target · SDR and HDR-DDR · up to 12.5 MHz
| Feature | Binho Supernova |
|---|---|
| I3C spec version | v1.0, v1.1.1, v1.2 |
| I3C controller | Yes |
| I3C target | Yes |
| I3C max clock speed | 12.5 MHz |
| SDR mode | Yes |
| HDR-DDR mode | Yes |
| Hot-Join | Yes |
| In-Band Interrupts | Yes |
| I3C max transaction size | 32 KB |
I2CController and target · up to 1 MHz · 7-bit and 10-bit addressing
| Feature | Binho Supernova |
|---|---|
| I2C controller | Yes |
| I2C target | Yes |
| I2C max clock speed | 1 MHz |
| 7-bit addressing | Yes |
| 10-bit addressing | Yes |
| Clock stretching | Yes |
| Configurable pull-up resistors | Yes |
| Number of I2C buses | 1 |
| I2C max transaction size | 32 KB |
SPIController and peripheral · up to 37.5 MHz · 4 chip selects
| Feature | Binho Supernova |
|---|---|
| SPI controller | Yes |
| SPI peripheral | Yes |
| SPI max clock speed (controller) | 37.5 MHz |
| SPI max clock speed (peripheral) | 16 MHz |
| All 4 SPI modes | Yes |
| Number of chip-select pins | 4 |
| Configurable MSB or LSB first | Yes |
| SPI max transaction size | 32 KB |
UARTUp to 2 Mbaud · hardware flow control
| Feature | Binho Supernova |
|---|---|
| UART max baud rate | 2 Mbaud |
| Hardware flow control | Yes |
| Dual-port monitor | No |
| 1-Wire support | No |
| RS-485 support | No |
| CAN-FD support | No |
Transfers of up to 32 KB move in a single transaction (see Large Transfers). The Supernova can also power the device under test from two rails at a time: the active I3C port’s and the Multifunction domain’s. The SPI peripheral role is not available on hardware revision B.
Higher-Level Protocols
Section titled “Higher-Level Protocols”The Supernova is also a good fit for the protocols that run on top of the protocols in the table above:
- JESD300-5 SPD (DDR5 SPD over I3C)
- NVMe-MI and MCTP over I3C (NVMe-MI over I3C, MCTP over I3C)
- MIPI I/Os over I3C Bridge
- MIPI Debug over I3C
- OIF CMIS
- MIPI CSI-2 Always On Sentinel Conduit
- SMBus (SMBus and Legacy I2C on the I3C Port)
Common Applications
Section titled “Common Applications”- Device driver and firmware development.
- Automated hardware and firmware tests.
- Flash and EEPROM programming.
- I2C, SMBus and PMBus testing.
- Emulating an I3C, I2C or SPI device before the silicon is available.
The full product datasheet is in the document library at my.binho.io, after signing in. Product page and ordering: Binho Supernova.
Software Support
Section titled “Software Support”| Software | Use it for |
|---|---|
| Mission Control 3 | Point-and-click tools for I2C, I3C, SPI, GPIO, the Serial Terminal and the Memory Programmer. Desktop app for Windows, macOS and Linux, or the web app at mc3.binho.io in a Chromium browser. |
| PyCosmicSDK | Python scripts and test automation. pip install pycosmicsdk. Every feature on this page, including target modes, SMBus on the I3C port and large transfers. Guides: binhollc.github.io/pycosmicsdk. |
| CosmicSDK | C, C++, C# and Java applications. Docs: binhollc.github.io/CosmicSDK. |
In the Box
Section titled “In the Box”
Binho Supernova kit
- 1× Binho Supernova USB Host Adapter
- I3C Port Kit
- 1× I3C harness terminated with 2.54 mm female headers
- 6× 1-position centered male-to-male pin headers
- 1× I3C port to 4-pin JST SH (Qwiic-compatible) adapter
- Dedicated I2C Port Kit
- 1× 4-pin JST SH (Qwiic-compatible) to 4-pin JST SH cable
- 1× 4-pin JST SH (Qwiic-compatible) cable with male headers
- 1× 4-pin JST SH (Qwiic-compatible) cable with female headers
- Multifunction Port Breakout Kit
- 1× 30-conductor IDC ribbon cable
- 1× ribbon cable to 2.54 mm pitch header breakout board
- USB Kit
- 1× USB Type-C to Type-A cable
- 1× USB Type-A to Type-C adapter
- Mounting Kit
- 2× mounting screws
- 2× washers
- 1× Custom protective zippered carry case
Relevant Accessories
Section titled “Relevant Accessories”Sold separately:
| Accessory | Use it for |
|---|---|
| I3C Target Board | Programmable I3C target. Accepts Bosch Shuttle 3.0 and STMicroelectronics DIL24 sensor evaluation boards. |
| PIC18-Q20 CNano Breakout | Microchip board with a native I3C target, for a first I3C bus. |
| mikroBUS Adapter Board | Connects MikroE Click boards over I3C, I2C, SPI or UART. Also fits the Pulsar. |
All accessories: Accessories.
Application Notes
Section titled “Application Notes”Application guides:
Application notes with code: STM32 flashing over I3C, Bosch, ST and TDK MEMS sensors, TMF8829 HDR-DDR. See Other examples.

